Factory size of Nissan Clipper Rio wheels and tolerances
Information updated on Jun. 12, 2022, 11:23Clipper Rio models were produced by Nissan from 2007 to 2012. There were 2 modifications of this car in total:
The manufacturer Nissan installed discs with a diameter of 13 to 13 inches on the Clipper Rio model. On this model, you can install 12 disk options, of which 12 factory and 0 are valid.
Nissan Clipper Rio: table of standard and permissible disk sizes
The table below shows all the parameters of Nissan Clipper Rio wheels that were produced in 2007-2012.
Legend of the table (parameters of PCD and offset of Nissan Clipper Rio discs):
- DIA (hole diameter)
- LZ (number of holes)
- PCD (hole circle diameter)
- ET (disk indent)
Modification | Production year | General parameters | Wheel diameter | PCD | Wheel width | ET (disk indent) | DIA (diameter) | Type of install |
---|---|---|---|---|---|---|---|---|
0.7i (U71W) | 2007 | 4.5Jx13 4/100 ET46 d56 | 13 | 4X100 | 4.5 | 46 | 56 | Factory |
0.7i (U72W) | 2007 | 4.5Jx13 4/100 ET46 d56 | 13 | 4X100 | 4.5 | 46 | 56 | Factory |
0.7i (U71W) | 2008 | 4.5Jx13 4/100 ET46 d56 | 13 | 4X100 | 4.5 | 46 | 56 | Factory |
0.7i (U72W) | 2008 | 4.5Jx13 4/100 ET46 d56 | 13 | 4X100 | 4.5 | 46 | 56 | Factory |
0.7i (U71W) | 2009 | 4.5Jx13 4/100 ET46 d56 | 13 | 4X100 | 4.5 | 46 | 56 | Factory |
0.7i (U72W) | 2009 | 4.5Jx13 4/100 ET46 d56 | 13 | 4X100 | 4.5 | 46 | 56 | Factory |
0.7i (U71W) | 2010 | 4.5Jx13 4/100 ET46 d56 | 13 | 4X100 | 4.5 | 46 | 56 | Factory |
0.7i (U72W) | 2010 | 4.5Jx13 4/100 ET46 d56 | 13 | 4X100 | 4.5 | 46 | 56 | Factory |
0.7i (U71W) | 2011 | 4.5Jx13 4/100 ET46 d56 | 13 | 4X100 | 4.5 | 46 | 56 | Factory |
0.7i (U72W) | 2011 | 4.5Jx13 4/100 ET46 d56 | 13 | 4X100 | 4.5 | 46 | 56 | Factory |
0.7i (U71W) | 2012 | 4.5Jx13 4/100 ET46 d56 | 13 | 4X100 | 4.5 | 46 | 56 | Factory |
0.7i (U72W) | 2012 | 4.5Jx13 4/100 ET46 d56 | 13 | 4X100 | 4.5 | 46 | 56 | Factory |